{"id":2002,"date":"2026-11-12T14:29:35","date_gmt":"2026-11-12T11:29:35","guid":{"rendered":"https:\/\/setaf2018.com\/?p=2002"},"modified":"2026-11-12T14:39:19","modified_gmt":"2026-11-12T11:39:19","slug":"atterberg-limits","status":"publish","type":"post","link":"https:\/\/setaf2018.com\/en\/post\/atterberg-limits\/","title":{"rendered":"Atterberg Limits: Liquid Limit, Plastic Limit and Plasticity Index"},"content":{"rendered":"\n<p class=\"wp-block-paragraph\">The Atterberg limits are the water contents at which a fine-grained soil passes from one state of consistency to the next: from liquid to plastic at the liquid limit, from plastic to semi-solid at the plastic limit, and from semi-solid to solid at the shrinkage limit. They were defined by Albert Atterberg in 1911 and adapted for engineering use by Casagrande in the 1930s.<\/p>\n\n\n\n<figure class=\"wp-block-image size-large\"><img decoding=\"async\" src=\"https:\/\/setaf2018.com\/wp-content\/uploads\/2026\/11\/atterberg-limits-blog_featured.webp\" alt=\"Atterberg Limits Testing: a technician running a Casagrande cup liquid limit test on clay paste in a soil laboratory\"\/><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">The tests are simple, inexpensive and run on disturbed material, which is why almost every site investigation report contains them. The liquid and plastic limits are measured on the fraction passing the 425 \u00b5m sieve, and their difference, the plasticity index, is the number most often carried forward into design.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">That number does more than classify. Compressibility estimates, undrained strength correlations and liquefaction screening of fine-grained soils all start from it, so an error made at the laboratory bench travels a long way.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The limits are indices rather than material constants, and the method used to measure them is part of the result.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">What Are the Atterberg Limits?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Three boundaries on a single scale of water content.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">As water is added to a dry clay, the soil passes from a brittle solid to a semi-solid that crumbles, then to a plastic material that can be moulded without cracking, and finally to a liquid that flows under its own weight. The Atterberg limits mark the three transitions, each expressed as a water content in per cent, the mass of water divided by the mass of dry solids.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The transitions are not sharp physical events, and a clay does not change phase at the liquid limit. Each limit is defined by a standardised test, and the water content at which the soil meets the test criterion is the limit by definition. That convention makes the limits reproducible between laboratories, and it also makes them dependent on the test.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Physically, the limits reflect how much water the clay minerals hold at their surfaces: a smectite-rich soil shows high limits; a kaolinite-dominated soil, with far less specific surface, shows low ones.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">How Is the Liquid Limit Measured?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Two families of test are in use, and they define the liquid limit through different mechanisms. Both are run on a uniform paste of soil passing the 425 \u00b5m sieve, with the water content of each trial obtained by oven drying.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Casagrande Cup (ASTM D4318)<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">In the method standardised by Casagrande (1932) and specified in ASTM D4318, a pat of paste is placed in a brass cup, a groove is cut through it, and the cup is dropped repeatedly onto a hard rubber base from a height of 10 mm, at two drops per second. The number of blows needed to close the groove over 13 mm is recorded.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The test is repeated at several water contents, and the liquid limit is read at 25 blows from the flow curve of water content against the logarithm of blow count. ASTM D4318 also permits a one-point method, which converts a single determination near 25 blows with an empirical factor, at some cost in reliability.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Fall Cone (BS 1377-2 \/ ISO 17892-12)<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">The fall cone replaces dynamic blows with quasi-static penetration. In the configuration of BS 1377-2 and ISO 17892-12, a cone of 80 g mass and 30\u00b0 apex angle is set with its tip touching the surface of the paste and released for 5 seconds. The liquid limit is the water content at which the penetration equals 20 mm, interpolated from several trials. ISO 17892-12 also recognises a 60 g, 60\u00b0 cone, for which the liquid limit is taken at 10 mm penetration.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Hansbo (1957) showed that cone penetration is governed by the undrained <a href=\"https:\/\/setaf2018.com\/en\/post\/shear-strength-of-soil\/\">shear strength of the soil<\/a>, so a cone liquid limit is close to a water content of constant strength.<\/p>\n\n\n\n<figure class=\"wp-block-image size-large\"><img decoding=\"async\" src=\"https:\/\/setaf2018.com\/wp-content\/uploads\/2026\/11\/atterberg-limits-blog_body-1.webp\" alt=\"Fall Cone Test: a fall cone penetrometer on clay paste beside rolled plastic limit threads\"\/><\/figure>\n\n\n\n<h2 class=\"wp-block-heading\">How Is the Plastic Limit Measured?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">By rolling a thread by hand, in both the ASTM and the BS\/ISO procedures.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A portion of the paste is rolled on a glass plate into a thread of uniform diameter. When the thread reaches 3.2 mm in ASTM D4318, or 3 mm in BS 1377-2, it is remoulded and rolled again, losing water with each cycle. The plastic limit is the water content at which the thread crumbles before reaching that diameter.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The result depends heavily on the operator&#8217;s pressure, rolling rate and judgement of crumbling. Wroth and Wood (1978) observed that the undrained strength at the plastic limit is roughly one hundred times that at the liquid limit, and cone-based alternatives build on that ratio, but thread rolling remains the standard method.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">When no thread can be rolled, or the plastic limit equals or exceeds the liquid limit, the soil is reported as non-plastic.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">What About the Shrinkage Limit?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">The shrinkage limit, ws, is the water content below which further drying produces no further reduction in volume: water continues to leave, but air enters the pores instead of the particles moving closer together.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The original mercury-displacement procedure of ASTM D427 has been withdrawn, and ASTM D4943 measures the volume of a dried pat after coating it in wax. BS 1377-2 includes a simpler linear shrinkage test. The shrinkage limit is used mainly in assessing shrink\u2013swell behaviour and is reported far less often than the other two limits.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Plasticity Index, Liquidity Index and Activity<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Three derived quantities carry most of the engineering information. The plasticity index is the range of water content over which the soil behaves plastically:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>PI = wL \u2212 wP<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">where PI is the plasticity index, also written Ip, wL the liquid limit and wP the plastic limit, all as water content in per cent.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A high plasticity index generally means high clay content, high compressibility and large volume change. Plotted against the liquid limit, it places the soil on the <a href=\"https:\/\/setaf2018.com\/en\/post\/plasticity-index-chart\/\">plasticity index chart<\/a> used for fine-grained soil classification.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The liquidity index locates the natural water content relative to the two limits:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>IL = ( wn \u2212 wP ) \/ PI<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">where IL is the liquidity index (dimensionless) and wn the natural water content in per cent.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Zero means the soil is at its plastic limit and one means it is at its liquid limit. Negative values are typical of desiccated or heavily overconsolidated clays, while values near or above one indicate a soft, often sensitive deposit that turns to slurry when remoulded. EN ISO 14688-2 uses the consistency index, IC = ( wL \u2212 wn ) \/ PI, which equals 1 \u2212 IL.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Activity, introduced by Skempton (1953), separates the quantity of clay from its type:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>A = PI \/ ( % finer than 2 \u00b5m )<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">where A is the activity (dimensionless) and the denominator is the clay fraction by mass, obtained from hydrometer analysis.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Skempton classed clays below 0.75 as inactive, between 0.75 and 1.25 as normal and above 1.25 as active, with values of around 0.4 for kaolinite, 0.9 for illite, 1.5 for calcium montmorillonite and above 7 for sodium montmorillonite.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table><thead><tr><th>Term<\/th><th>Symbol<\/th><th>Units<\/th><th>Meaning<\/th><\/tr><\/thead><tbody><tr><td>Liquid limit<\/td><td>wL<\/td><td>%<\/td><td>Boundary between plastic and liquid states<\/td><\/tr><tr><td>Plastic limit<\/td><td>wP<\/td><td>%<\/td><td>Water content at which a 3 mm thread crumbles<\/td><\/tr><tr><td>Shrinkage limit<\/td><td>ws<\/td><td>%<\/td><td>Water content below which drying causes no volume reduction<\/td><\/tr><tr><td>Plasticity index<\/td><td>PI (Ip)<\/td><td>%<\/td><td>Range of water content over which the soil is plastic<\/td><\/tr><tr><td>Liquidity index<\/td><td>IL<\/td><td>dimensionless<\/td><td>Position of the natural water content between the limits<\/td><\/tr><tr><td>Activity<\/td><td>A<\/td><td>dimensionless<\/td><td>Plasticity index per unit clay fraction<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<h2 class=\"wp-block-heading\">Comparing the Liquid Limit Test Methods<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Thread rolling is included because every plasticity index depends on it.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table><thead><tr><th>Method<\/th><th>Input required<\/th><th>Particularly suited to<\/th><th>Main limitation<\/th><\/tr><\/thead><tbody><tr><td>Casagrande cup (ASTM D4318)<\/td><td>Trials bracketing 25 blows; calibrated drop height and base<\/td><td>Continuity with correlations built on cup data<\/td><td>Operator-dependent; groove slides in low-plasticity soils<\/td><\/tr><tr><td>Fall cone, 80 g \/ 30\u00b0 (BS 1377-2, ISO 17892-12)<\/td><td>Trials bracketing 20 mm penetration; calibrated cone<\/td><td>Low-plasticity soils; repeatability; link to undrained strength<\/td><td>Not interchangeable with cup values in high-plasticity clays<\/td><\/tr><tr><td>Thread rolling (plastic limit)<\/td><td>Paste worked by hand to crumbling<\/td><td>The plastic limit in ASTM and BS\/ISO practice<\/td><td>Strongly operator-dependent; poor repeatability<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<h2 class=\"wp-block-heading\">Why Do the Cup and the Cone Not Give the Same Liquid Limit?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Because they measure different responses and give both the same name.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The cup measures resistance to flow under repeated impact. Closure of the groove is a small slope failure driven by a sequence of shocks, and the energy each blow delivers depends on the drop height, the mass of the cup and the resilience of the base. The response combines the soil&#8217;s strength, density and rate sensitivity, and the operator influences it. Even cups built to different standards can disagree, because base hardness controls how much of each impact reaches the soil.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The cone measures static penetration governed by undrained strength and is far less operator-dependent.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The cone criteria were chosen to match the cup over the common range of soils, and at low and intermediate plasticity the two generally agree. As plasticity rises the values drift apart, and in high-plasticity clays neither method has a stronger claim to being correct. This matters because the classical correlations, including those of Skempton (1957) and of Terzaghi and Peck (1967), were built on cup data.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>A liquid limit is not a property of the clay alone. It is a property of the clay and the test.<\/strong><\/p>\n\n\n\n<h2 class=\"wp-block-heading\">What Do the Limits Decide in Design?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Three decisions, each made before any advanced test.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The first is compressibility. For normally consolidated clays of low to moderate sensitivity, Terzaghi and Peck (1967) related the compression index to the liquid limit:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Cc \u2248 0.009 \u00b7 ( wL \u2212 10 )<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">where Cc is the compression index (dimensionless) and wL the liquid limit in per cent.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Skempton (1944) had earlier proposed 0.007 \u00b7 ( wL \u2212 10 ) for remoulded clays. Neither applies to overconsolidated, sensitive or organic soils. The estimate screens <a href=\"https:\/\/setaf2018.com\/en\/post\/foundation-settlement-analysis\/\">consolidation settlement<\/a>; the design value comes from an <a href=\"https:\/\/setaf2018.com\/en\/post\/oedometer-consolidation-test\/\">oedometer test<\/a>.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The second is strength. Skempton (1957) related the undrained strength of normally consolidated clay to plasticity as su \/ \u03c3\u2032v = 0.11 + 0.0037 \u00b7 PI, so the plasticity index sets the ratio and the vertical effective stress, which depends on the groundwater level and the <a href=\"https:\/\/setaf2018.com\/en\/post\/saturated-unit-weight-of-soil\/\">saturated unit weight<\/a> of each layer, sets the magnitude.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The third is liquefaction screening. The Chinese criteria as presented by Seed and Idriss (1982) treated a fine-grained soil as potentially liquefiable if its fraction finer than 5 \u00b5m was below 15 per cent, its liquid limit below 35 per cent and its natural water content above 0.9 times the liquid limit. Ground failures in silty soils, including Adapazar\u0131 in the 1999 Kocaeli earthquake, shifted attention to plasticity index. Bray and Sancio (2006) classed soils with a plasticity index below 12 and wn \/ wL above 0.85 as susceptible, and those with a plasticity index of 12 to 18 and wn \/ wL above 0.8 as moderately susceptible. These criteria screen susceptibility only; triggering requires a cyclic <a href=\"https:\/\/setaf2018.com\/en\/post\/liquefaction-analysis-in-geotechnical-engineering\/\">liquefaction analysis<\/a>.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For a clay with wL = 52, wP = 24, wn = 38 and a clay fraction of 35 per cent, the plasticity index is 28, the liquidity index 0.50 and the activity 0.80, in Skempton&#8217;s normal range. If normally consolidated, the estimated compression index is about 0.38 and the normalised undrained strength about 0.21. With wn \/ wL of about 0.73, it falls outside the Bray and Sancio susceptibility bounds.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>The limits do not replace a consolidation test or a strength test. They decide which tests are needed and what results to expect.<\/strong><\/p>\n\n\n\n<h2 class=\"wp-block-heading\">How Do Sample Preparation and Drying Change the Result?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Substantially.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Drying before testing reduces the limits of some soils irreversibly, most markedly organic soils and tropical residual or volcanic soils containing halloysite or allophane. ASTM D4318 describes both wet and dry preparation, and the choice has to be reported. <a href=\"https:\/\/setaf2018.com\/en\/post\/uscs-soil-classification\/\">ASTM D2487<\/a> uses the effect deliberately: a fine-grained soil whose oven-dried liquid limit is less than 0.75 times its undried value is classified as organic.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A paste tested immediately after mixing has not hydrated uniformly and gives low limits. In marine clays, replacing saline pore water with distilled water also changes the limits. Where much of the sample is retained on the 425 \u00b5m sieve, the limits describe the matrix only.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">When Are Atterberg Limits Not Appropriate?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Where the soil has no meaningful plasticity, or where its behaviour is governed by something the remoulded paste does not retain.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Clean sands and gravels are non-plastic. Peats and fibrous organic soils do not form a uniform paste. Sensitive clays, structured soils and residual soils lose in the test the structure that gives them their in-situ strength, so the limits describe destructured material. A liquidity index above one flags sensitivity but cannot quantify it.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Common Errors in Atterberg Limit Testing<\/h2>\n\n\n\n<figure class=\"wp-block-table\"><table><thead><tr><th>Error<\/th><th>Consequence<\/th><\/tr><\/thead><tbody><tr><td>Organic or residual soil oven-dried before testing<\/td><td>Limits reduced irreversibly; classification shifted<\/td><\/tr><tr><td>Cup and cone results mixed without identification<\/td><td>Method difference read as natural variability<\/td><\/tr><tr><td>One-point liquid limit reported as multipoint<\/td><td>Hidden loss of reliability in borderline cases<\/td><\/tr><tr><td>Paste tested immediately after mixing<\/td><td>Incomplete hydration; limits underestimated<\/td><\/tr><tr><td>Limits measured on different subsamples<\/td><td>Inconsistent or implausible plasticity index<\/td><\/tr><tr><td>Terzaghi and Peck correlation used on overconsolidated clay<\/td><td>Settlement substantially overestimated<\/td><\/tr><tr><td>Test method not stated in the report<\/td><td>Reviewer cannot judge which correlations apply<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<h2 class=\"wp-block-heading\">Where SETAF2018 Fits<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">SETAF2018 treats the Atterberg limits as part of the material definition. In the Physical Properties tab of each material, the natural water content, liquid limit, plastic limit and shrinkage limit are entered, and the Calculate button derives the plasticity index and the liquidity index together with the void ratio, porosity, degree of saturation and unit weights.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The limits are inputs, not laboratory processing: blow counts, cone penetrations and flow curves remain in the laboratory record, and the value entered is the limit the laboratory reports.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The correlation tabs draw on the same values. In the Shear Strength tab, the Skempton (1957) relationship estimates the undrained strength of normally consolidated clay from the plasticity index and the vertical effective stress, and a friction angle correlation also uses the plasticity index. The Kulhawy and Mayne (1990) correlation estimates the overconsolidation ratio from the liquidity index. Calculated values are transferred into the material with the Apply button, so a derived parameter stays traceable to the limits, alongside consolidation results from the <a href=\"https:\/\/setaf2018.com\/en\/laboratory-experiments\/\">laboratory testing<\/a> module.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For fine-grained layers, liquefaction is checked with the Adapazar\u0131 criterion, which requires the liquidity index or wn \/ wL, the liquid limit, the plasticity index and the clay content to fall within set bounds, and with the Ishihara criterion, which assesses whether a liquefiable layer at depth can affect the surface given the thickness of the non-liquefying layer above it.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">In the <a href=\"https:\/\/setaf2018.com\/en\/graphs-and-analyses\/\">graphs<\/a> module, the natural water content, liquid limit and plastic limit are plotted against depth on one graph, with the plasticity index on a separate one, showing where the natural water content approaches the liquid limit.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Because the limits belong to the material, each layer carries them into every check that uses the shared <a href=\"https:\/\/setaf2018.com\/en\/soil-profile\/\">soil profile<\/a>.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Frequently Asked Questions<\/h2>\n\n\n\n<h3 class=\"wp-block-heading\">What are the Atterberg limits?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">They are the water contents at which a fine-grained soil changes consistency: the liquid limit between liquid and plastic, the plastic limit between plastic and semi-solid, and the shrinkage limit below which drying causes no further volume loss. Each is defined by a standardised laboratory test.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">What is the difference between the liquid limit and the plastic limit?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">The liquid limit is the water content at which the soil begins to flow, and the plastic limit the water content at which it stops being mouldable and crumbles. The first is measured with the Casagrande cup or fall cone, the second by rolling a thread to about 3 mm.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">How is the plasticity index calculated?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">By subtracting the plastic limit from the liquid limit, PI = wL \u2212 wP, both in per cent. A clay with a liquid limit of 52 and a plastic limit of 24 has a plasticity index of 28. A soil whose plastic limit cannot be determined is reported as non-plastic.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Why do the Casagrande cup and the fall cone give different liquid limits?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Because they define the limit through different mechanisms. The cup measures groove closure under repeated blows, which depends on base hardness, density and the operator; the cone measures static penetration governed by undrained strength. They agree reasonably at low and intermediate plasticity and diverge in high-plasticity clays.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">What does the liquidity index tell the engineer?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">It shows where the natural water content sits between the two limits. A value near zero means the soil is at its plastic limit and typically stiff; a value near one means it is soft and probably sensitive; a negative value indicates a desiccated or heavily overconsolidated clay.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">What is clay activity?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">It is the plasticity index divided by the percentage of particles finer than 2 \u00b5m, as defined by Skempton (1953). Below 0.75 a clay is inactive, typical of kaolinite; between 0.75 and 1.25 normal; above 1.25 active, typical of smectites with high swelling potential.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Can Atterberg limits be used for sands?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">No. Clean sands and gravels are non-plastic, and no thread can be rolled from them. In silty or clayey sands the limits describe only the fraction passing 425 \u00b5m and must be read with the fines content.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Do Atterberg limits predict compressibility?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Only approximately. Terzaghi and Peck (1967) related the compression index to the liquid limit as 0.009 \u00b7 ( wL \u2212 10 ) for normally consolidated clays of low to moderate sensitivity. The estimate suits preliminary design, overestimates settlement in overconsolidated clays and does not replace an oedometer test.<\/p>\n\n\n\n<script type=\"application\/ld+json\">{\"@context\": \"https:\/\/schema.org\", \"@type\": \"FAQPage\", \"mainEntity\": [{\"@type\": \"Question\", \"name\": \"What are the Atterberg limits?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"They are the water contents at which a fine-grained soil changes consistency: the liquid limit between liquid and plastic, the plastic limit between plastic and semi-solid, and the shrinkage limit below which drying causes no further volume loss. Each is defined by a standardised laboratory test.\"}}, {\"@type\": \"Question\", \"name\": \"What is the difference between the liquid limit and the plastic limit?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"The liquid limit is the water content at which the soil begins to flow, and the plastic limit the water content at which it stops being mouldable and crumbles. The first is measured with the Casagrande cup or fall cone, the second by rolling a thread to about 3 mm.\"}}, {\"@type\": \"Question\", \"name\": \"How is the plasticity index calculated?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"By subtracting the plastic limit from the liquid limit, PI = wL \u2212 wP, both in per cent. A clay with a liquid limit of 52 and a plastic limit of 24 has a plasticity index of 28. A soil whose plastic limit cannot be determined is reported as non-plastic.\"}}, {\"@type\": \"Question\", \"name\": \"Why do the Casagrande cup and the fall cone give different liquid limits?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"Because they define the limit through different mechanisms. The cup measures groove closure under repeated blows, which depends on base hardness, density and the operator; the cone measures static penetration governed by undrained strength. They agree reasonably at low and intermediate plasticity and diverge in high-plasticity clays.\"}}, {\"@type\": \"Question\", \"name\": \"What does the liquidity index tell the engineer?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"It shows where the natural water content sits between the two limits. A value near zero means the soil is at its plastic limit and typically stiff; a value near one means it is soft and probably sensitive; a negative value indicates a desiccated or heavily overconsolidated clay.\"}}, {\"@type\": \"Question\", \"name\": \"What is clay activity?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"It is the plasticity index divided by the percentage of particles finer than 2 \u00b5m, as defined by Skempton (1953). Below 0.75 a clay is inactive, typical of kaolinite; between 0.75 and 1.25 normal; above 1.25 active, typical of smectites with high swelling potential.\"}}, {\"@type\": \"Question\", \"name\": \"Can Atterberg limits be used for sands?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"No. Clean sands and gravels are non-plastic, and no thread can be rolled from them. In silty or clayey sands the limits describe only the fraction passing 425 \u00b5m and must be read with the fines content.\"}}, {\"@type\": \"Question\", \"name\": \"Do Atterberg limits predict compressibility?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"Only approximately. Terzaghi and Peck (1967) related the compression index to the liquid limit as 0.009 \u00b7 ( wL \u2212 10 ) for normally consolidated clays of low to moderate sensitivity. The estimate suits preliminary design, overestimates settlement in overconsolidated clays and does not replace an oedometer test.\"}}]}<\/script>\n","protected":false},"excerpt":{"rendered":"<p>How Atterberg limits are measured \u2014 liquid limit, plastic limit and plasticity index \u2014 and why the same clay gives different values in the cup and the cone.<\/p>\n","protected":false},"author":1,"featured_media":1992,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":"","rank_math_title":"Atterberg Limits: Liquid Limit, Plastic Limit and Plasticity Index","rank_math_description":"How Atterberg limits are measured \u2014 liquid limit, plastic limit and plasticity index \u2014 and why the same clay gives different values in the cup and the cone.","rank_math_focus_keyword":"atterberg limits"},"categories":[51],"tags":[],"class_list":["post-2002","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-soil-parameters"],"_links":{"self":[{"href":"https:\/\/setaf2018.com\/en\/wp-json\/wp\/v2\/posts\/2002","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/setaf2018.com\/en\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/setaf2018.com\/en\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/setaf2018.com\/en\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/setaf2018.com\/en\/wp-json\/wp\/v2\/comments?post=2002"}],"version-history":[{"count":2,"href":"https:\/\/setaf2018.com\/en\/wp-json\/wp\/v2\/posts\/2002\/revisions"}],"predecessor-version":[{"id":2016,"href":"https:\/\/setaf2018.com\/en\/wp-json\/wp\/v2\/posts\/2002\/revisions\/2016"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/setaf2018.com\/en\/wp-json\/wp\/v2\/media\/1992"}],"wp:attachment":[{"href":"https:\/\/setaf2018.com\/en\/wp-json\/wp\/v2\/media?parent=2002"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/setaf2018.com\/en\/wp-json\/wp\/v2\/categories?post=2002"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/setaf2018.com\/en\/wp-json\/wp\/v2\/tags?post=2002"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}